-
-
Befestigen Sie das Netzteil mit einem 2,5 mm Inbusschlüssel am Rahmen. Ziehen Sie die M4x10 Schrauben noch nicht ganz fest; wir werden dies später nachholen.
-
-
-
Kontrollieren Sie, ob die Position des Schalters auf der Seite des Netzteils richtig ist.
-
-
-
Bevor Sie fortfahren, prüfen Sie bitte noch einmal, ob das Kabel korrekt verbunden und ordentlich am Heizbett befestigt ist.
-
Das SCHWARZE Kabel muss an "GND" angeschlossen werden
-
Das ROTE Kabel muss an "VCC" angeschlossen werden
-
Die Kabelabdeckung (die später montiert wird) setzt voraus, dass die Anschlüsse leicht zueinander gebogen werden. Biegen Sie sie durch leichten Druck, aber lassen Sie einen Spalt zwischen ihnen.
-
-
-
Legen Sie M3n Muttern in das gedruckte Teil ein.
-
Falls Sie die M3n Mutter nicht hineindrücken können, wenden Sie keine übermässige Kraft an. Drehen Sie stattdessen eine M3 Schraube von der anderen Seite des gedruckten Teils ein. Beim Anziehen der Schraube wird die Mutter hineingezogen. Geben Sie acht, dass das gedruckte Teil beim Anziehen nicht bricht.
-
-
-
Dehnen Sie das schwarze/weiße Thermistorenkabel nicht vollständig. Lassen Sie das Kabel unter dem Heizbett etwas lose. Dies verhindert, dass sich das Kabel überdehnt und die Verbindung in der Mitte des Heizbetts unterbrochen wird, wenn sich das Heizbett während des Druckens bewegt.
-
Führen Sie das schwarze Thermistorenkabel zum Kabel der Heizbett-Heizung und wickeln Sie es ein paar Mal um dieses herum (siehe Bild).
-
-
-
Nun wickeln Sie das Kabel komplett in die textile Kabelhülle.
-
Wenn Sie fertig sind, verdrehen Sie die Hülle leicht (nicht die Kabel im Inneren). Die Hülle wird sich gleichmäßig um das Kabelbündel wickeln.
-
-
-
M3x8r Schrauben (4x)
-
Die Druckoberfläche (gelbliche Folie) ist bereits auf das Heizbett aufgebracht, ENTFERNEN SIE SIE NICHT und seien Sie besonders vorsichtig, um die Oberfläche nicht zu beschädigen.
-
mit gelötetem Kabel: gehen Sie bitte zu Schritt 21
-
-
-
M3x8r Schraube (1x)
-
M3 Mutter (1x)
-
Führen Sie das schwarze Thermistorenkabel unter das Kabel der Heizbett-Heizung und wickeln Sie es ein paar Mal um dieses herum (siehe Bild).
-
-
-
Nehmen Sie das Filamentstück, das mit den Teilen mitgeliefert wurde (Länge ungefähr 30 cm).
-
Schieben Sie es ganz in das Loch für das Filament in der Heizbett-Kabelabdeckung hinein. Falls Sie Probleme beim Hineinschieben des Filaments haben, nehmen Sie die Spitzzange, um das Filament am Ende zuzuspitzen.
-
-
-
Wickeln Sie die Kabelspirale um die Kabel vom Heizbett, inklusive dem NYLON-Filament. Fangen Sie mit einer oder zwei Wicklungen 1 cm hinter der Heizbett-Kabelabdeckung an.
-
Wenn die erste Umwicklung fertiggestellt ist, schieben Sie sie in die Heizbett-Kabelabdeckung hinein.
-
-
-
Inspizieren Sie den Drucker von oben und kontrollieren Sie, dass die Linien auf dem Heizbett perfekt parallel mit den Stangen der X-Achse ausgerichtet sind, wie im Bild gezeigt.
-
Falls sie nicht parallel ausgerichtet sind, benutzen Sie den 17 mm Schlüssel, um die M10 Muttern einzustellen, bis alles stimmt. Benutzen Sie nur die Muttern auf der Seite, die am nächsten zum Motor der Z-Achse liegt.
-
Dies ist sehr wichtig. Falls sie nicht parallel sind, werden Sie später bei der Kalibrierung Probleme haben!
-
Wenn Sie die Muttern anpassen, stellen Sie sicher, dass die M10 Gewindestange ganz bis unten im Schlitz eingeführt ist.
-
M3x10 Schraube (3x)
-
Heizbett-Kabelabdeckung (1x)
-
-
-
Insert M3n nuts in the printed part.
-
In case you can't press the M3n nut in, don't use excessive force. Take the M3 bolt and thread it from the opposite side of the printed part, as you tighten the screw, it will pull the nut in. Be careful not the break the printed part during tightening.
-
-
-
Place the heatbed-cable-cover on the heatbed to cover the soldered cables and LED.
-
Tighten the cover to the heatbed using M3x10 screw and Allen key. Be careful not to pinch (break) any wires from the heatbed!
-
-
-
Guide the black thermistor cable next to the heatbed heater cable and wrap it few times around (see the photo).
-
-
-
Use the textile sleeve and wrap the cables from the heatbed. Start by few centimeters of the sleeve behind the heatbed cover.
-
When the first "wrap" is ready, slide it inside the heatbed cover. Ensure it is at least 5-6 mm.
-
Before you continue with wrapping the sleeve, we need to fix it in the cable cover. Please proceed to the next step.
-
-
-
Place second part of the cover on the top of the textile sleeve.
-
Insert two screws M3x10 and tighten them, proceed with caution and tighten both screws equally.
-
Your tightened cover should look like the last picture.
-
-
-
Now, finish wrapping the cable into the textile sleeve.
-
When done, slightly twist the sleeve (not the cables inside). The sleeve will evenly wrap all around the cable bundle.
-
-
-
Remove the M3 nuts highlighted in the picture.
-
-
-
Using 2mm allen key, tighten the heatbed to the Y-carriage.
-
-
-
Tighten the Y-belt holder to the heatbed using the supplied 2.5 mm Allen key.
-
If you have the Y-belt-holder with a slot, make sure that the screws are in the middle as shown in the picture.
-
-
-
M3x8r screw (1 pc)
-
M3 nut (1 pcs)
-
Lead the black thermistor cable under the heatbed heater cable and wrap it few times around (see the photo).
-
-
-
Take the piece of filament that came with the parts ( length around 30 cm ).
-
Push it all the way down in the filament holder hole in the heat bed cable cover. If you experience difficulties when inserting the filament use pliers to make a sharp tip on the filament.
-
-
-
Make sure the filament is pointing to the right while the cable holder is oriented upwards (see the nut)
-
Tighten the part to the heatbed using 2 mm Allen key. Be careful not to pinch (break) any wires from the heatbed!
-
-
-
Use the spiral wrap and wrap the cables from the heatbed including the NYLON. Start by one or two wraps 1 cm behind the heatbed cover.
-
When the first wrap is ready, slide it inside the heatbed cover.
-
-
-
Place a zip tie around the heatbed holder to tighten the spiral wrap with cables. There is a channel around the cover designed for the zip tie.
-
Cut the remaining part of the zip tie and continue with wrapping the spiral wrap.
-
-
-
Take a look on the printer from the top side and make sure that lines on heatbed are perfectly parallel with the X axis rods as shown in the picture.
-
If they are not in parallel position, use 17 mm wrench to adjust the M10 nuts to get it correct. Use nuts only on the side close to left Z axis motor.
-
-
-
Assemble the spool holders to the top of the frame as shown in the picture.
-
To properly assemble the spool holder, let the "tooth" sit on the frame and then press in the direction of the arrows (rotate backwards, while slightly pressing downwards).
-
Don't try to assemble spool holder by pushing it only from the top. More force is needed and you may damage the holder.
-
Almost there! You're one step away from finishing! Continue by connecting the electronics in the next chapter - 8. Zusammenbau der Elektronik
-
Cancel: I did not complete this guide.
9 other people completed this guide.